S4M EPL Menu Details
Article ID: 22275694
Topic or Information S4M EPL LCD Display Menu EPL Front Panel Details Applies To S4M Printer using E53 EPL firmware Details
|
S4M (EPL Model) Menu |
Menu Item | Options | Default Setting |
EPL Command | Option Description |
Password | ||||||||||||
Password Level 1 and 2 menu (no password needed) |
|||||||||||||||||
PRINTER READY |
|||||||||||||||||
DENSITY 9 |
0-15 | 9 | D Read More> |
Burn time | None |
||||||||||||
TEAROFF 0 |
-120 - +120 | 0 | Q |
Dot rows away from tearoff bar |
|||||||||||||
LABELTOP 0 |
-120 - +120 | 0 | R Read More> |
Defines top margin of label |
|||||||||||||
MEDIA TYPE GAP/NOTCH |
GAP/NOTCH | GAP/NOTCH | Q Read More> |
Chooses which sensor is used, also what type of label is loaded |
|||||||||||||
CONTINUOUS | |||||||||||||||||
MARK | |||||||||||||||||
SENSOR SELECT REFLECTIVE |
REFLECTIVE | REFLECTIVE | Refers to media type |
||||||||||||||
TRANSMISSIVE | |||||||||||||||||
REMOVAL TEAR |
TEAR | TEAR | O Read More> |
What mode do you want the printer to operate in |
|||||||||||||
REWIND | |||||||||||||||||
DELAYED CUT | |||||||||||||||||
CUTTER | |||||||||||||||||
PEEL | |||||||||||||||||
PRINT SPEED 6 IPS |
2, 3, 4, 5, 6 IPS | 6 IPS | S Read More> |
Print rate while printing |
|||||||||||||
LENGTH AUTO |
AUTO | AUTO | Used in conjunction with calibration |
||||||||||||||
1-39" | |||||||||||||||||
Password Level 3 menu (password = 1234) |
|||||||||||||||||
ADVANCED SETUP 3 |
enter password 1234 <enter> to see next set of menu items |
1234
|
|||||||||||||||
PRINT OUT SETTINGS
|
SETTINGS | SETTINGS | Prints a config | ||||||||||||||
ALL | Prints all these lists | ||||||||||||||||
IMAGES | List resident images | ||||||||||||||||
FORMATS | Lists resident formats | ||||||||||||||||
FONTS | Lists resident fonts | ||||||||||||||||
PARALLEL COMM. UNIDIRECTIONAL |
UNIDIRECTIONAL | UNIDIRECTIONAL | |||||||||||||||
BIDIRECTIONAL | |||||||||||||||||
BAUD 9600 |
1200, 2400 4800, 9600, 19200, 38400, 57600, 115200 |
9600 | Y Read More> |
Baud rate of the printers serial port | |||||||||||||
DATA BITS 8 BITS |
8 BITS | 8 BITS | Data bit setting of the serial port | ||||||||||||||
7 BITS | |||||||||||||||||
PARITY NONE |
NONE | NONE | Parity setting of the serial port | ||||||||||||||
EVEN | |||||||||||||||||
ODD | |||||||||||||||||
HOST HANDSHAKE DTR & XON/XOFF |
DTR & XON/XOFF | DTR & XON/XOFF | Handshake setting of the serial port | ||||||||||||||
DTR | |||||||||||||||||
HEXDUMP NO |
NO | NO | Normal printing mode | ||||||||||||||
YES | dump | Enable hex dump print mode | |||||||||||||||
CHANGE RTC DATE* | hitting enter shows date | * This menu item will not be present if RTC option is not installed |
|||||||||||||||
CHANGE RTC TIME* | hitting enter shows time | * This menu item will not be present if RTC option is not installed |
|||||||||||||||
LOAD DEFAULTS |
If you press the enter button at this point you'll be prompted with ARE YOU SURE? YES |
^default Read More> |
Printer can be defaulted by hitting the ENTER button when the prompt reads: ARE YOU SURE? YES |
||||||||||||||
INITIALIZE FLASH MEM YES |
If you press the enter button at this point you'll be prompted with ARE YOU SURE? YES |
E: flash memory can be initialized by hitting the ENTER button when the prompt reads: ARE YOU SURE? YES |
|||||||||||||||
RIBBON YES |
YES | YES | O | Setting for thermal transfer or direct thermal |
|||||||||||||
NO | OD, Od Read More> |
||||||||||||||||
EPL OVERRIDE DISABLED |
DISABLED | DISABLED | |||||||||||||||
ENABLED | |||||||||||||||||
SENSOR PROFILE |
If you press the enter button at this point a sensor profile will print |
The printed profile can be used to to troubleshoot calibration problems |
|||||||||||||||
MEDIA/RIBBON CALIBRATE |
Performs manual calibration | ||||||||||||||||
LANGUAGE ENGLISH |
|
ENGLISH | Selects the language for the display |
Password Level 4 menu (password = 9999) |
|||||
ADVANCED SETUP 4 |
enter password 9999 <enter> to see next set of menu items |
9999
|
|||
LABEL LEVEL 13 |
50 | ||||
PAPER OUT 64 |
0 | ||||
PAPER GAIN 10 |
calibrated value | ||||
RIBBON OUT 55 |
calibrated value | ||||
RIBBON GAIN 26 |
calibrated value | ||||
TAKE LABEL* 66 |
*appears in display if take label option is installed | ||||
MEDIA POWER UP CALIBRATION |
CALIBRATION | CALIBRATION | Autocalibrates | ||
FEED | Feeds to first web after sensor | ||||
NO MOTION | No media feed | ||||
SHORT CAL | Cals label length using current sensor settings | ||||
LENGTH | Cals based on last label length setting | ||||
MEDIA HEAD CLOSE CALIBRATION |
CALIBRATION | CALIBRATION | Autocalibrates | ||
FEED | Feeds to first web after sensor | ||||
NO MOTION | No media feed | ||||
SHORT CAL | Cals label length using current sensor settings | ||||
LENGTH | Cals based on last label length setting | ||||
LANGUAGE ENGLISH |
|||||
DENSITY 9 |

+ Product Codes
- S4M
- S4M Series